+- Yealink Forums (http://forum.yealink.com/forum)
+-- Forum: IP Phone Series (/forumdisplay.php?fid=4)
+--- Forum: Configuration (/forumdisplay.php?fid=24)
+--- Thread: Expansion Modules (/showthread.php?tid=2327)
Expansion Modules - BFeller - 08-27-2014 11:47 PM
I have a Yealink T26 phone. I would like to assign a blf to the buttons on the separate expansion module using the config template. However, I can not get the information to come out right. Here's what I've got so far....
##########################################################################################
## Expansion Module 1 ##
##########################################################################################
#X ranges from 1 to 16, Y ranges from 1 to 40.
#expansion_module.x.key.y.type = 37 (Switch by default)
#expansion_module.x.key.y.line = 0
#expansion_module.x.key.y.value =
#expansion_module.x.key.y.pickup_value =
#expansion_module.x.key.y.label =
#expansion_module.X.key.Y.xml_phonebook =
#Expansion module1 key1
{IF blf11}
expansion_module.1.key.1.type = %%DKtype%%
expansion_module.1.key.1.line = %%Line%%
expansion_module.1.key.1.value = %%blf11%%
expansion_module.1.key.1.pickup_value = %%PickupValue%%
expansion_module.1.key.1.label = %%blffirstname11%% %%blflastname11%%
expansion_module.1.key.1.xml_phonebook =
{ELSE}
expansion_module.1.key.1.type = 37
expansion_module.1.key.1.label = List 1
{ENDIF}
#Expansion module1 key2
{IF blf12}
expansion_module.1.key.2.type = 16
expansion_module.1.key.2.line = 1
expansion_module.1.key.2.value = 1001
expansion_module.1.key.2.pickup_value = *20*
expansion_module.1.key.2.label = John Doe
expansion_module.1.key.2.xml_phonebook =
{ELSE}
expansion_module.1.key.2.type = NA
{ENDIF}
#Expansion module1 key3
{IF blf13}
expansion_module.1.key.3.type = 16
expansion_module.1.key.3.line = 1
expansion_module.1.key.3.value = 1002
expansion_module.1.key.3.pickup_value = *20*
expansion_module.1.key.3.label = Jane Doe
expansion_module.1.key.3.xml_phonebook =
{ELSE}
expansion_module.1.key.3.type = NA
{ENDIF}
...and so on and so on. However, no matter what values I try to add to the "value", "line", and "type" lines, I either get a blank spot on the line on the LCD screen of the module, or I get "blf" (when trying to use '16' as the value in the second type field instead of 'NA')
What I'm ultimately trying to do is assign an extension to a key on the module.
RE: Expansion Modules - Yealink Support - 08-29-2014 08:38 PM
Hi BFeller,
What you really want to do is assigning a blf to the buttons on the separate expansion module via auto provision,right.
I have tested phone on 3CX in my side, and using the template like below:
And the Memory key LED is solid green when the monitored user is idle.
But fast flashing red (200ms),when the monitored user receives an incoming call.
When the monitored user is idle, the supervisor presses the BLF key to dial out the phone number. When the monitored user receives an incoming call, the supervisor presses the BLF key to pick up the call directly. When the monitored user is in a call, the supervisor presses the BLF key to interrupt and set up a conference call.
Thx