T38G needs new firmware released - Printable Version +- Yealink Forums (http://forum.yealink.com/forum) +-- Forum: IP Phone Series (/forumdisplay.php?fid=4) +--- Forum: Phone specific topic (/forumdisplay.php?fid=12) +---- Forum: T3xP Series (/forumdisplay.php?fid=22) +---- Thread: T38G needs new firmware released (/showthread.php?tid=1233) |
RE: T38G needs new firmware released - John_K - 08-29-2014 03:03 AM It has multicast reception, There's no Multicast page option in the Type field for DSS Key programming RE: T38G needs new firmware released - Greysi - 09-01-2014 04:16 PM Try DSS Key x Type: Paging Value: [IP]:[Port] //Listening Adress of MulticastIP RE: T38G needs new firmware released - cwestin66 - 09-03-2014 04:05 PM Yes I agree. I have several T-28's and the last update has a BLF level feature.. One of the complaints I have received from color blind customers using Asterisk was BLF lights was always on. They could not tell the red form green. I hope they add this feature to the T-38's. RE: T38G needs new firmware released - John_K - 09-11-2014 08:32 AM (09-01-2014 04:16 PM)Greysi Wrote: Try Nope, It tries to dial the string. Call from '7554' (192.168.8.88:1062) to extension '224.0.2.60:50010' rejected because extension not found Paging isn't Multicast Paging. RE: T38G needs new firmware released - Greysi - 09-11-2014 06:31 PM Phone: Yealink T38G FW: 38.70.0.221 Web-Site of Phone: Contacts\MulitcastIP Paging Barge : Disabled Paging Priority Active: Enabled IP Adress: 244.0.0.32:10111 DSS Key\Line Key Line Key4 Type: Paging Value: 244.0.0.32:10111 Label: Test I test it in this second and it's working (for me). RE: T38G needs new firmware released - sdebelloiii - 10-01-2014 05:52 AM Greysi, Do you have this working on a Voice VLAN on the Internet Port and a Data VLAN on the PC Port? I believe that is where Multicast Paging stops working. Thanks for your response. (09-11-2014 06:31 PM)Greysi Wrote: Phone: Yealink T38G RE: T38G needs new firmware released - Greysi - 10-01-2014 02:35 PM It's working. Of course only for voice-vlan 26. phone settings: Network\advanced\VLAN\ Internet Port: Active: Enabled VID: 26 Pc Port: Active: Disabled pc settings: only dhcp (no vlan configurations) the cisco-switch config: interface FastEthernet1/0/4 description *** PCs and PHONES *** switchport access vlan 13 switchport mode access switchport voice vlan 26 srr-queue bandwidth share 10 10 60 20 srr-queue bandwidth shape 10 0 0 0 mls qos trust cos auto qos voip trust spanning-tree portfast RE: T38G needs new firmware released - innatech - 11-18-2014 04:04 AM It has multicast reception, There's no Multicast page option in the Type field for DSS Key programming Right. On later firmwares, i.e. the ones my most recently received units shipped with, there is a 'Paging' type in the menu, but no way to configure the listening address (the multicast submenu under contacts is missing). Older firmwares with the multicast patch (38.70.0.172) have the multicast submenu under the contacts tab, but there's no way to select the paging type when cofiguring a line or memory key. Maybe it can be done via a provisioning file, but it's not there in the web interface. Currently the only correctly configured phone I have was an accident: I programmed the line key on the newer firmware before realizing I had to downgrade to .172 to set the listening address. The line key programming was retained. This is embarrassingly shoddy QA and this will probably be my last Yealink deployment if this is the level of competence and support that we can expect. Can anyone specify a T38g firmware load that has BOTH the ability to configure a multicast paging key and the multicast listening address from the web UI? RE: T38G needs new firmware released - jasit - 11-18-2014 04:08 AM the most current firmware that works with multicast 38.70.1.26 RE: T38G needs new firmware released - innatech - 11-18-2014 04:26 AM I upgraded a test unit to 38.70.1.26 .... there's still no option to setup a Paging or Multicast Paging key. See attached images. [attachment=1163] [attachment=1164] Alright, now the options are showing up in Chrome but not in Firefox. Tell me that isn't weird! [attachment=1165] Will test with this 70.1.26 version and hopefully I can standardize on that so long as whatever 3CX specific tweaks it contains aren't a problem when used w/Elastix (Asterisk/FreePBX). |