Yealink Forums
Make softkey Page button for 3CX (v12) - Printable Version

+- Yealink Forums (http://forum.yealink.com/forum)
+-- Forum: IP Phone Series (/forumdisplay.php?fid=4)
+--- Forum: Phone specific topic (/forumdisplay.php?fid=12)
+---- Forum: T3xP Series (/forumdisplay.php?fid=22)
+---- Thread: Make softkey Page button for 3CX (v12) (/showthread.php?tid=1118)



Make softkey Page button for 3CX (v12) - printwest - 12-20-2013 07:45 AM

I would like to make a Page All button. When I pickup the handset, is it possible to make it the 3rd softkey button between "123" and "cancel".

Is it also possible to make this part of the phone provisioning, so I don't have to change each phone.

I've assigned the Virtual machine number (extension) '07' as my Page All number in 3CX.


RE: Make softkey Page button for 3CX (v12) - Yealink Support - 12-20-2013 05:07 PM

Hi printwest,

Why don't you use a multicast paging feature?
We have released a new firmware with multicast for 3CX.
You can click below link to download and test.
T32G:
ftp://yealinkftp:yealinkftp@ftp.yealink.com/T3X/T3X-V70/32.70.0.198.rom
T38G:
ftp://yealinkftp:yealinkftp@ftp.yealink.com/T3X/T3X-V70/38.70.0.198.rom


RE: Make softkey Page button for 3CX (v12) - printwest - 12-21-2013 04:23 AM

Ok, but I still need a BUTTON for paging.


RE: Make softkey Page button for 3CX (v12) - Yealink Support - 12-23-2013 04:12 PM

Hi printwest,

If this feature is urgent, please contact with your distributor. They have higher priority than the forum.


RE: Make softkey Page button for 3CX (v12) - jasit - 01-03-2014 03:25 AM

here is part of my 3cx yealinkt3x.ph.xml file

################################################################################​#######
## Multicast ##
################################################################################​#######

#Configure the codec of multicast paging.
multicast.codec =

#Enbale or diable the phone to handle the incoming multicast paging calls when there is a multicast paging call on the phone; 0-Disabled, 1-Enabled (default);
#If enabled, the phone will answer the incoming multicast paging call with a higher priority and ignore that with a lower priority.
multicast.receive_priority.enable =

#Configure the priority of multicast paging calls. It ranges from 0 to 10.
multicast.receive_priority.priority =

#Configure the listening multicast IP address and port number for the phone. X ranges from 1 to 10.
#multicast.listen_address.X.ip_address =
multicast.listen_address.1.ip_address = 224.0.0.32:10000

#Configure the lable displayed on the LCD screen when receiving the multicast paging. X ranges from 1 to 10.
#multicast.listen_address.X.label =
multicast.listen_address.1.label = Office Page


then under the programmable keys I changed the third key to be paging.

programablekey.3.type =13
programablekey.3.line =
programablekey.3.value = 8001
programablekey.3.xml_phonebook =
programablekey.3.history_type =
programablekey.3.label = Paging



8001 is the extention that my 3cx system uses. you could also just use the yealink multicast paging, not sure how that works.