Using the latest firmware, 28.72.0.205 for the T46, I'm having a problem disabling codecs through autoprovisioning. Here is my configuration:
Code:
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 1
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 1
account.1.codec.2.payload_type = G722
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 9
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = PCMA
account.1.codec.3.priority =
account.1.codec.3.rtpmap = 8
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G729
account.1.codec.4.priority =
account.1.codec.4.rtpmap = 18
As of right now, in the GUI, it has the following codecs enabled in their respective order:
PMCU
G722
G729
G722
G722 is listed twice, and I'm not sure why the codecs aren't being properly disabled.
Please use below sequence just disable or enable the codes. Or change the priority of them.
------------------------------------------
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 1
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 0
account.1.codec.2.payload_type = PCMA
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 8
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = G723_53
account.1.codec.3.priority =0
account.1.codec.3.rtpmap = 4
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G723_63
account.1.codec.4.priority = 0
account.1.codec.4.rtpmap = 4
account.1.codec.5.enable = 0
account.1.codec.5.payload_type = G729
account.1.codec.5.priority = 3
account.1.codec.5.rtpmap = 18
account.1.codec.6.enable = 1
account.1.codec.6.payload_type = G722
account.1.codec.6.priority = 4
account.1.codec.6.rtpmap = 9
account.1.codec.7.enable = 0
account.1.codec.7.payload_type = iLBC
account.1.codec.7.priority = 0
account.1.codec.7.rtpmap = 106
account.1.codec.8.enable = 0
account.1.codec.8.payload_type = G726-16
account.1.codec.8.priority = 0
account.1.codec.8.rtpmap = 103
account.1.codec.9.enable = 0
account.1.codec.9.payload_type = G726-24
account.1.codec.9.priority = 0
account.1.codec.9.rtpmap = 104
account.1.codec.10.enable = 0
account.1.codec.10.payload_type = G726-32
account.1.codec.10.priority = 0
account.1.codec.10.rtpmap = 102
account.1.codec.11.enable = 0
account.1.codec.11.payload_type = G726-40
account.1.codec.11.priority = 0
account.1.codec.11.rtpmap = 105
account.1.codec.12.enable = 0
account.1.codec.12.payload_type = GSM
account.1.codec.12.priority = 0
account.1.codec.12.rtpmap = 3
------------------------------------------
(03-27-2014 07:37 PM)Yealink Support Wrote: [ -> ]Please use below sequence just disable or enable the codes. Or change the priority of them.
------------------------------------------
account.1.codec.1.enable = 1
account.1.codec.1.payload_type = PCMU
account.1.codec.1.priority = 1
account.1.codec.1.rtpmap = 0
account.1.codec.2.enable = 0
account.1.codec.2.payload_type = PCMA
account.1.codec.2.priority = 2
account.1.codec.2.rtpmap = 8
account.1.codec.3.enable = 0
account.1.codec.3.payload_type = G723_53
account.1.codec.3.priority =0
account.1.codec.3.rtpmap = 4
account.1.codec.4.enable = 0
account.1.codec.4.payload_type = G723_63
account.1.codec.4.priority = 0
account.1.codec.4.rtpmap = 4
account.1.codec.5.enable = 0
account.1.codec.5.payload_type = G729
account.1.codec.5.priority = 3
account.1.codec.5.rtpmap = 18
account.1.codec.6.enable = 1
account.1.codec.6.payload_type = G722
account.1.codec.6.priority = 4
account.1.codec.6.rtpmap = 9
account.1.codec.7.enable = 0
account.1.codec.7.payload_type = iLBC
account.1.codec.7.priority = 0
account.1.codec.7.rtpmap = 106
account.1.codec.8.enable = 0
account.1.codec.8.payload_type = G726-16
account.1.codec.8.priority = 0
account.1.codec.8.rtpmap = 103
account.1.codec.9.enable = 0
account.1.codec.9.payload_type = G726-24
account.1.codec.9.priority = 0
account.1.codec.9.rtpmap = 104
account.1.codec.10.enable = 0
account.1.codec.10.payload_type = G726-32
account.1.codec.10.priority = 0
account.1.codec.10.rtpmap = 102
account.1.codec.11.enable = 0
account.1.codec.11.payload_type = G726-40
account.1.codec.11.priority = 0
account.1.codec.11.rtpmap = 105
account.1.codec.12.enable = 0
account.1.codec.12.payload_type = GSM
account.1.codec.12.priority = 0
account.1.codec.12.rtpmap = 3
------------------------------------------
Thanks, worked like a charm!